Process
pasteurisation
gelato mix cooling
food safety

Gelato Mix Cooling Rate After Pasteurisation: Speed Limits

Marco Freire, chef and creator of Free Gelato Balancing App
Marco Freire
Chef and creator of Free Gelato Balancing App
8 min read
A stainless steel pasteuriser in a clean italian gelato lab with a jug of pale gelato mix and a probe thermometer on a marble counter
A stainless steel pasteuriser in a clean italian gelato lab with a jug of pale gelato mix and a probe thermometer on a marble counter

Pasteurising a gelato mix kills pathogens; cooling it decides whether the mix stays safe and when ageing can start. Here are the time limits regulators actually write down, the heat a real batch has to lose, and how to size your cooling method so a 10 kg mix reaches 4 °C on schedule.

A stainless steel pasteuriser in a clean italian gelato lab with a jug of pale gelato mix and a probe thermometer on a marble counter

The heat goes in fast. The real work of a pasteurising cycle is taking it out again.

Recipes and quick fixes on Instagram: @freegelatobalancing

Why cooling is half of pasteurisation

Pasteurisation is the biological control point of the process. Douglas Goff's ice cream technology text at the University of Guelph describes it as the step designed for the destruction of pathogenic bacteria, which also reduces spoilage organisms such as psychrotrophs and helps hydrate proteins and stabilisers. What it does not do is sterilise. A hot mix that then sits for hours in the warm middle temperatures is treated by food codes as a risk, which is why the rules below put a clock on the cooling, not only on the heating.

The second reason is production. Goff's text sets ageing at or below 5 °C for at least four hours, usually overnight, so the fat can crystallise and the proteins and polysaccharides can fully hydrate. That clock only starts once the mix is cold. A batch that takes four hours to come down from 85 °C pushes the whole maturazione step, and the churning that follows, into the next shift. Our gelato production timeline shows how tightly those steps chain together.

The cooling limits regulators actually write down

There is no single world rule for a gelato mix cooling rate. Three texts give clear numbers, and they agree more than they differ; a fourth, the EU rule, sets only a principle.

SourceApplies toFromToTime limit
UK Dairy Products (Hygiene) Regulations 1995, Sch. 6 Part V (revoked in England from 2006)Pasteurised ice cream mixAfter 65.6 °C/30 min, 71.1 °C/10 min or 79.4 °C/15 s7.2 °C or below1.5 hours, then held cold until freezing
FDA Food Code 3-501.14 (adopted by US states, e.g. WAC 246-215-03515)Cooked time/temperature control for safety food57 °C21 °C, then 5 °C2 hours to 21 °C, 6 hours in total to 5 °C
Virginia 2VAC5-510-560Ice cream mix after heat treatmentPasteurising temperature7.2 °C or below"Promptly", then held cold
EU Regulation 852/2004, Annex II Ch. IX (6)Any food held chilled after heatingHeat treatmentA temperature without risk to health"As quickly as possible"

The UK 1995 rule was revoked in England from 1 January 2006, when the EU hygiene package took over, but it remains the clearest number ever written for an ice cream mix. The EU text gives no number, so a sensible choice is to work to the strictest written figure you can find. Check your own local authority and your HACCP plan: the table tells you what the numbers look like, not what your inspector will accept.

Quick reference. Write your critical limit as a number you can measure: mix from pasteurising temperature to 7 °C or below within 90 minutes, then to 4 °C for ageing at or below 5 °C. Log the time at 85 °C, at 21 °C and at 7 °C on every batch, with a calibrated thermometer probed in the centre of the container, not at the wall.

Chart of gelato mix cooling limits: 85 °C at the end of the hold, 7.2 °C within 90 minutes and 21 °C within 2 hours, above an ageing band at 5 °C or below

Figure 1. Two written limits on one chart: 7.2 °C within 90 minutes (UK 1995 ice cream rule, revoked in England in 2006) and 21 °C within 2 hours (FDA Food Code first stage).

A stainless steel container of pale gelato mix sitting in a large basin of ice water in a clean italian gelato lab

Worked example: how much heat a 10 kg batch must lose

Cooling speed is a heat problem, and the size of the problem comes straight out of the recipe. Take a balanced milk gelato mix of 1000 g built in the balancer: 620 g whole milk, 150 g cream at 35% fat, 150 g sucrose, 40 g dextrose, 35 g skim milk powder and 5 g stabiliser. With the app's ingredient values it lands at 36.3% total solids, 7.5% fat, 9.7% MSNF, 3.6% protein, 18.6% sugars, 63.7% water, POD 184 and PAC 272. All of that sits inside the milk gelato range, and by the PAC divided by -20 rule it serves at about -13.6 °C. Our guide on how to balance a gelato recipe explains each band.

Now ask the question a refrigeration engineer would ask: how many kilojoules does that mix hold? Composition based models from food engineering (Choi and Okos) give a specific heat for each component: about 4.18 kJ/kg·K for water, 2.0 for protein and fat and 1.55 for carbohydrate at 0 °C. Weighted by this mix, the specific heat averages about 3.30 kJ/kg·K between 4 and 85 °C, roughly a fifth less than plain water. Solids hold less heat than water, so a richer mix is slightly easier to cool.

BatchHeat to remove, 85 to 4 °CAverage cooling power to hit 7.2 °C in 90 minIce melted (theoretical minimum)
1 kg267 kJabout 50 W0.8 kg
10 kg2,674 kJabout 480 W8.0 kg
30 kg8,022 kJabout 1,430 W24.0 kg

The ice column uses the latent heat of fusion of ice, about 334 kJ/kg: every kilo of ice that melts absorbs that much heat. It is a floor, not a target, because a real ice bath also absorbs heat from the room and from its own container. The power column is the average the cooling equipment has to sustain for 90 minutes, before any losses.

Two decisions fall out of this table. First, a 10 kg batch needs about 8 kg of ice actually melting, so an ice bath for that size means a basin that holds more ice than mix, refilled as it melts. Second, the cooling load scales with the batch, not with the container. Splitting 10 kg into four shallow pans does not reduce the 2,674 kJ, it only lets the heat leave faster through more surface.

Choosing a cooling method for your batch size

Every method below can meet the limits. The difference is how much attention it needs from you.

  • Pasteuriser with integrated cooling. Combined units heat, hold and then cool in the same vessel. One Italian maker describes its cycle as heating to 85 °C followed by rapid cooling to 4 °C, with the cooling set point adjustable between 2 and 6 °C. This is the least handling and the easiest to log. See our guide to pasteurizer types and the ageing tank that often follows.
  • Plate or tube heat exchanger. The industrial route. Goff notes that the cooling sections of ice cream mix HTST presses are usually larger than those for milk, because the preheated mix arrives warm and regeneration is lost. Our pasteurization deep-dive compares HTST, LTLT and UHT.
  • Ice water bath. Cheap and effective for small batches if you size it with the table above, stir the mix and keep the water moving. Salt in the ice water pushes the bath below 0 °C and speeds the first stage.
  • Blast chiller with shallow containers. Fast, provided the mix is spread thin. Washington's adoption of the FDA Food Code lists shallow, uncovered layers of two inches (about 5 cm) or less, in equipment holding 5 °C or colder, as one accepted cooling method. A blast chiller set for chilling, not deep freezing, is the right cycle here.
  • Walk-in or reach-in fridge alone. The slowest path. Cold rooms are built to keep cold food cold. A deep pot of hot mix pushed straight in can sit in the warm band far longer than any limit allows and warms everything around it.

Mistakes that slow the curve

Most cooling failures come from geometry and habit, not equipment.

  1. Deep, covered containers. Heat leaves through surface. A tall lidded pot cools from the outside in, and the centre lags far behind the wall reading.
  2. Measuring at the wrong point. The critical reading is the warmest point, the centre of the container. A probe resting against cold steel will pass a batch that is not cold.
  3. Stopping the stir. Stirring moves hot mix to the cold wall. Without it, an ice bath builds a cold skin and an insulated warm core.
  4. Adding flavourings too early. Fruit, sauces and inclusions go in after ageing, at the batch freezer, or in a step your HACCP plan covers. They do not belong in a warm, half cooled base.
  5. Treating ageing as cooling. Ageing is a cold rest at or below 5 °C. It starts when the mix is already there, not while it is still coming down. Our article on gelato mix aging sets out what happens in that tank.

Speed also protects the work done in the heat. Stabilisers that hydrated at pasteurising temperature, explained in our stabilizer hydration guide, and fat globules reduced in the homogenisation step reach the ageing tank exactly as you formulated them.

A row of shallow stainless steel pans of pale gelato mix cooling on a rack inside a clean italian gelato lab

A cooling protocol you can run tomorrow

  1. Before you heat, weigh the batch and note it on the log. The batch weight tells you the heat load from the table above.
  2. Pasteurise to your validated time and temperature, then start the cooling clock the moment the hold ends.
  3. Cool to 7 °C or below within 90 minutes, stirring if you use a bath, spreading thin if you use a blast chiller.
  4. Log the centre temperature at the end of the hold, at the 21 °C crossing and at 7 °C, with the times.
  5. Finish at 4 °C, cover, label and age at or below 5 °C for at least four hours.
  6. Any batch that misses the limit gets the action your HACCP plan defines. Do not quietly churn it.

A clipboard cooling log with temperatures and times beside a covered stainless steel ageing container in a clean gelato lab

pasteurisation
gelato mix cooling
food safety
haccp
gelato production

Frequently asked questions

Common questions about process.

Continue reading

View all

You read the theory. Now run the numbers.

Open the free balancer, plug in your own ingredients, and apply what you just read. PAC, POD, MSNF, Total Solids, all updated live as you adjust the recipe. Free account, no credit card.

Start Balancing for Free

542 accounts created so far.